Completes the lockout-prevention work: a standing audit for configurations
RouterOS accepts but that do not work, an empirical answer on /system history
undo, and corrections to the VLAN cache the editors are built on.
Config Health (new)
Eleven rules over a live snapshot, encoding MikroTik's documented Layer2
misconfigurations plus the latent lockout cases: IP or VLAN interface on a
bridge slave port, a bridged VLAN interface, a bond slave that is also a
bridge port, MTU above L2MTU, a multi-VLAN entry with untagged ports,
bridges competing for hardware offload, a port in no VLAN on a filtering
bridge, a PVID that frame-type=admit-only-vlan-tagged makes inert, a VLAN
interface whose VLAN the bridge is not tagged in, duplicate addresses, and
management that survives only on a dynamic entry. Each finding names the
consequence, the fix, how long it has been present, and the vendor doc.
Runs hourly, surfaces on the Security tab and the dashboard.
Calibrated against hardware: RouterOS 7 relocates an address off a bridge
slave port onto the bridge (actual-interface), so the stock defconf layout
works. Reporting that as critical would have fired on a default install; it
is informational unless RouterOS did not relocate it.
Change Guard: severed-connection handling
Proven on a CRS by deleting its own management address — the switch locked
itself out and self-restored unattended in ~3 minutes, twice.
That test exposed a real defect. withSafeApply treated any exception from
the apply step as "the change failed", disarming the guard and rethrowing.
But the most dangerous changes sever the connection carrying them, so the
call times out even though the change applied. The guard was stripping the
safety net off a device that had just gone silent, and reporting HTTP 500
"Read timeout" instead of telling the user the device was restoring itself.
Only luck saved it: the disarm needed the same dead connection.
Reachability now decides, not the exception. Unreachable leaves the revert
armed and returns auto_reverting; still reachable means a genuine failure,
disarmed so nothing reboots for nothing. committed_at is no longer stamped
on failed or reverted guards; resolved_at records completion instead.
/system history undo probe
probeUndoCapability tests the device rather than assuming. On 7.23.x over
the binary API: /system/history/print works, /system/history/undo does not
exist, /undo numbers= rejects the parameter, bare /undo works. Undo is
therefore untargeted, and cannot replace auto-revert since a dead-man switch
must fire after contact is lost. Binary restore stays the default.
VLAN cache correctness
- vlans keyed on (device_id, bridge, vlan_id); the old key collapsed the
same VID on two bridges
- vlan-ids ranges expanded instead of parseInt truncating "10-20" to 10
- both VLAN tables pruned, but only when the device returned an
authoritative list, so a failed read leaves the cache stale not empty
- bridge_vlan_entries.vlan_ids written and .tagged derived rather than
hardcoded false, which had left the port editor unable to see a trunk
- removeBridgeVlan matched by expanded VIDs; the ?vlan-ids= server filter
compares raw strings, so deleting one VID of a range silently no-opped
while reporting success. Multi-VLAN entries are refused in the route,
before the guard arms, since a mid-apply failure would cost a reboot
- interfaces.vlan_filtering promoted to a column
Membership is deliberately the STATIC tagged/untagged, never current-*.
These tables back the editors and updateBridgeVlan is remove-then-add, so
whatever is shown is written back; the effective view baked RouterOS's
dynamic PVID entries into saved configuration on every save. Analysis that
needs the effective view reads the device live. Extracted to pure functions
with tests, because that path was previously untestable inline.
Verified on four devices; 195 backend tests; all CI gates green.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
2GT-RichandClaude Opus 5
93ff1fbc53